Do you know how many watts is a factory car stereo? If you feel underwhelmed by your factory car stereo – you are not alone. 83% of car owners have reported that their car stereo provides a disappointing experience when they crank up the volume.
A factory-installed car stereo will work fine if you are looking for a mild background ambient sound. However, it’s not enough if you are looking for a powerful experience and do not want to compromise with the quality of audio hitting your eardrums.
Comparing car stereos across the spectrum, it turns out that in general, the default car stereo which comes factory fitted in your car fails to satisfy your audio requirements.
That’s especially true if you are a hardcore audiophile who wants a near to perfect audio experience (including the time you spend traveling in your car).
How many watts is a factory car stereo?
It is very important that you know the wattage of your car stereo. Most times, the wattage is low, somewhere around 8 to 10 watts RMS per chanel. To find out the power of your head unit, type in the make and model to google search.
Most standard factory car stereos usually have no more than about 10 watts RMS maximum output power per channel.
This misunderstanding is caused by the difference between peak wattage and RMS wattage.
A more powerful 200-watt aftermarket stereo, for example, probably gets its power from an amp chip rated at 50 watts peak by 4 channels, and its real world RMS rating is probably in the neighborhood of 15-18 watts per channel.
Good power, but it pales in comparison to a strong external car amplifier. That’s usually not enough power to overcome road noise without sounding shrill. The watts of your factory installed car stereo will influence the performance of your speaker.
What are watts?
A watt is a unit power. Unless your speakers have power amps built in, they don’t have any. So don’t be confused when you see in the speaker wattage mentioned in a particular speaker’s specifications.
Even non-powered speakers may have wattage ratings (mentioned in the specifications). But that is only to indicate its ability to handle power. If your speaker is rated at 200 watts then it means it can handle 200 watts of power.
Watt is a unit for measuring electrical power and the Watts of an amp-speaker duo is the power that the system can withstand under specific conditions.
Watts specification of a speaker alone does not tell you how loud the speaker can play. You have to know the amplifier’s operating power (in Watts RMS as well as peak wattage) complemented with the speaker’s efficiency (sensitivity), measured in decibels (db).
Generally high sensitivity speakers are in the 90db and higher range. Those speakers will perform well in less power. This is important as most times our factory system doesn’t have a lot of power.
So higher efficiency speakers will sound better than lower efficiency speakers when we are using a factory radio.
In the factory installed setting the amps which are installed are mostly of low watt. Thus the speakers are not able to produce optimum results. If we push the amp to perform beyond its capacity, then the speakers will produce a distorted sound.
What to do?
Solution 1: Replace the factory stereo with a new one- with higher RMS wattage.
Solution 2: Replace the speakers with newer ones (high sensitive ones, high sensitivity speakers are the 90db and higher range). The high sensitive speakers work well under less power wattage.
Solution 3: You can add additional amps which will complement the inbuilt amps. This again helps with improving the audio without tinkering with the entire factory inbuilt structure. This requires a lot of effort in terms of cost and time and might turn out altogether ineffective without proper expertise.
When adding external amps, you need to make sure that the added wattage is matching the speaker’s capacity. If required replace the inbuilt speakers with newer ones to match the added wattage (power) of the stereo.
Also, it is important to note that watts will not tell you if the amplifier can damage the speaker. Speakers are more often destroyed by distortion than electrical power.
Why is a stereo with more watts better?
More wattage usually means ‘better Dynamic Headroom’ and ‘lower distortion’. Dynamic headroom means the capacity of a system to reproduce loud sounds without distortions. It depends on the RMS wattage of the amp and the Peak wattage of the speaker.
Loud momentary music passages (such as the high lead part of a guitar solo or upper scales of a female vocalist) can reach as high as 200-300 watts (Peak wattage).
If the amplifier doesn’t have that much power in reserve (Dynamic Headroom), then the result would be higher distortion (THD to be more specific) and lower quality sound.
If you are considering a more powerful car stereo then you should take a look at the Alpine CDE -172BT it supplies 18 watts RMS x 4 channels – which in standard audio language is 4 x 50 watts = A 200-watt stereo. The sound this thing produces is unbelievable!
More watts = more power
Generally speaking, more watts in the stereo means more power it can handle. Thus, if you are unhappy with the performance of the factory-installed vehicle stereo, I’d advise you to go for the modification options as mentioned above (solutions).
Most reasonably priced aftermarket speakers will perform well with about 25 watts RMS or about 50 watts max per channel, but try to make sure that your amp’s output matches what your speakers can handle. The amp’s wattage should match the speaker’s capacity and vice versa for optimum performance.
A great aftermarket speaker to look at is the Rockford Fosgate R165 Full Range 3 – way Coaxial Speaker, these are perfect for replacing factory car speakers, they feature polypropylene cones, a silk dome Piezo tweeter and midrange.
Most factory installed car stereos are of average quality and performance. So, broadly speaking, you have two options. Fit a high quality aftermarket stereo, or fit uprated speakers. My suggestion would be to fit both.